微企帮做网站,wordpress主题动漫,找网站开发人员,wordpress 挂载对象存储实验
一、实验思路 1.先按照上图配置IP地址及环回
2.写缺省使公网可通
3.让R1、R4、R5每台路由器均成为中心站点形成全连网状结构拓扑
4.让R1成为中心站点R2R3为分支站点
5.分区域宣告ospf之后更改ospf在虚拟接口Tunnel工作方式为broadcast及让R1 当选DR
二、上虚拟机操作…实验
一、实验思路 1.先按照上图配置IP地址及环回
2.写缺省使公网可通
3.让R1、R4、R5每台路由器均成为中心站点形成全连网状结构拓扑
4.让R1成为中心站点R2R3为分支站点
5.分区域宣告ospf之后更改ospf在虚拟接口Tunnel工作方式为broadcast及让R1 当选DR
二、上虚拟机操作
1.配置IP地址及环回
[r1]int g0/0/0 [r1-GigabitEthernet0/0/0]ip add 6.1.1.1 24 [r1-GigabitEthernet0/0/0]int g0/0/1 [r1-GigabitEthernet0/0/1]ip add 16.1.1.1 24 [r1-GigabitEthernet0/0/1]int l0 [r1-LoopBack0]ip add 192.168.1.1 24
[r2]int g0/0/0 [r2-GigabitEthernet0/0/0]ip add 26.1.1.1 24 [r2-GigabitEthernet0/0/0]int l0 [r2-LoopBack0]ip add 192.168.2.1 24
[r3]int g0/0/0 [r3-GigabitEthernet0/0/0]ip add 36.1.1.1 24 [r3-GigabitEthernet0/0/0]int l0 [r3-LoopBack0]ip add 192.168.3.1 24
[r4]int g0/0/0 [r4-GigabitEthernet0/0/0]ip add 46.1.1.1 24 [r4-GigabitEthernet0/0/0]int l0 [r4-LoopBack0]ip add 192.168.4.1 24
[r5]int g0/0/0 [r5-GigabitEthernet0/0/0]ip add 56.1.1.1 24 [r5-GigabitEthernet0/0/0]int l0 [r5-LoopBack0]ip add 192.168.5.1 24
[r6]int g0/0/0 [r6-GigabitEthernet0/0/0]ip add 6.1.1.2 24 [r6-GigabitEthernet0/0/0]int g0/0/1 [r6-GigabitEthernet0/0/1]ip add 16.1.1.2 24 [r6-GigabitEthernet0/0/1] [r6-GigabitEthernet0/0/1]int g0/0/2 [r6-GigabitEthernet0/0/2]ip add 26.1.1.2 24 [r6-GigabitEthernet0/0/2] [r6-GigabitEthernet0/0/2]int g2/0/0 [r6-GigabitEthernet2/0/0]ip add 36.1.1.2 24 [r6-GigabitEthernet2/0/0] [r6-GigabitEthernet2/0/0]int g3/0/0 [r6-GigabitEthernet3/0/0]ip add 46.1.1.2 24 [r6-GigabitEthernet3/0/0] [r6-GigabitEthernet3/0/0]int g4/0/0 [r6-GigabitEthernet4/0/0]ip add 56.1.1.2 24 [r6-GigabitEthernet4/0/0] [r6-GigabitEthernet4/0/0]int l0 [r6-LoopBack0]ip add 6.6.6.6 24
2.写缺省
[r1]ip route-static 0.0.0.0 0 6.1.1.2 [r1]ip route-static 0.0.0.0 0 16.1.1.2
[r2]ip route-static 0.0.0.0 0 26.1.1.2
[r3]ip route-static 0.0.0.0 0 36.1.1.2
[r4]ip route-static 0.0.0.0 0 46.1.1.2
[r5]ip route-static 0.0.0.0 0 56.1.1.2
3.让R1、R4、R5每台路由器均成为中心站点形成全连网状结构拓扑
[r1-Tunnel0/0/0]int t0/0/1 [r1-Tunnel0/0/1]ip add 192.168.7.1 24 [r1-Tunnel0/0/1]tunnel-protocol gre p2mp [r1-Tunnel0/0/1]source 16.1.1.1 [r1-Tunnel0/0/1]nhrp entry 192.168.7.2 46.1.1.1 register [r1-Tunnel0/0/1]nhrp entry 192.168.7.3 56.1.1.1 register [r1-Tunnel0/0/1]nhrp entry multicast dynamic [r1-Tunnel0/0/1]nhrp network-id 200
[r4-Tunnel0/0/0]ip add 192.168.7.2 24 [r4-Tunnel0/0/0]tunnel-protocol gre p2mp [r4-Tunnel0/0/0]source 46.1.1.1 [r4-Tunnel0/0/0]nhrp entry 192.168.7.1 16.1.1.1 register [r4-Tunnel0/0/0]nhrp entry multicast dynamic
[r4-Tunnel0/0/0]nhrp network-id 200
[r5]int t0/0/0 [r5-Tunnel0/0/0]ip add 192.168.7.3 24 [r5-Tunnel0/0/0]tunnel-protocol gre p2mp [r5-Tunnel0/0/0]source 56.1.1.1 [r5-Tunnel0/0/0]nhrp entry multicast dynamic
[r5-Tunnel0/0/0]nhrp network-id 200 4.让R1成为中心站点R2R3为分支站点
[r1]interface Tunnel0/0/0 [r1-Tunnel0/0/1] ip address 192.168.0.1 24 [r1-Tunnel0/0/1] tunnel-protocol gre p2mp [r1-Tunnel0/0/1] source 6.1.1.1 [r1-Tunnel0/0/1] nhrp entry multicast dynamic [r1-Tunnel0/0/1] nhrp network-id 100
[r2]int t0/0/0 [r2-Tunnel0/0/0]ip add 192.168.0.2 24 [r2-Tunnel0/0/0]tunnel-protocol gre p2mp [r2-Tunnel0/0/0]source GigabitEthernet 0/0/0 [r2-Tunnel0/0/0]nhrp entry 192.168.0.1 6.1.1.1 register [r2-Tunnel0/0/0]nhrp network-id 100
[r3]int t0/0/0 [r3-Tunnel0/0/0]ip add 192.168.0.3 24 [r3-Tunnel0/0/0]tunnel-protocol gre p2mp [r3-Tunnel0/0/0]source g0/0/0 [r3-Tunnel0/0/0]nhrp entry 192.168.0.1 6.1.1.1 register [r3-Tunnel0/0/0]nhrp network-id 100 5.分区域宣告ospf之后更改ospf在虚拟接口Tunnel工作方式为broadcast及让R1 当选DR
区域0
[r1-ospf-1-area-0.0.0.0] network 192.168.0.1 0.0.0.0 [r1-ospf-1-area-0.0.0.0] network 192.168.1.1 0.0.0.0
[r2-ospf-1-area-0.0.0.0] network 192.168.0.2 0.0.0.0 [r2-ospf-1-area-0.0.0.0] network 192.168.2.1 0.0.0.0
[r3-ospf-1-area-0.0.0.0] network 192.168.0.3 0.0.0.0 [r3-ospf-1-area-0.0.0.0] network 192.168.3.1 0.0.0.0 区域1
[r1-ospf-1-area-0.0.0.1] network 192.168.7.1 0.0.0.0
[r4-ospf-1-area-0.0.0.1]network 192.168.4.1 0.0.0.0 [r4-ospf-1-area-0.0.0.1] network 192.168.7.2 0.0.0.0
[r5-ospf-1-area-0.0.0.1]network 192.168.5.1 0.0.0.0 [r5-ospf-1-area-0.0.0.1]network 192.168.7.3 0.0.0.0 在R1-R5更改ospf在虚拟接口Tunnel工作方式为broadcast ospf network-type broadcast
让R1 当选DR
在R2-R5更改ospf在虚拟接口Tunnel优先级为0 ospf dr-priority 0
三、检验
1.看一下R1-R6路由表 2.R1-R5环回互ping
